Usage&Maintenance Method Of Sanitary Ware 2

Bath room, shower screen use and maintenance method:

Subject 1, shower room, shower screen by toughened glass, long-term erosion of various alkaline bath water will make the shower room, shower screen glass attached on the Yellow scale. When cleaning, can be sprayed with special glass cleaning agent, and then wipe dry cloth can be bright as new.

2, for connecting shower room, shower screen parts of the hardware parts, can not use any cleaning agent to clean, so as to avoid corrosion and influence the service life. The easiest way is to clean the dirt with a dry cloth every week to keep it clean.

Bath tub use and maintenance method:

Daily cleaning and washing available general liquid detergent 1, bath cloth and soft not available ingredients containing a ketone or chlorine. Disinfection, containing formic acid and formaldehyde containing disinfectant.

2, if there are scratches on the surface of the bathtub or cigarette burns, just use 2000# water sandpaper to polish, and then coated with toothpaste, soft cloth can be polished as bright as new.

3, the bath surface scale with a soft towel dipped with light acidic detergent, such as lemon juice, vinegar wipe.

4, hydraulic friction cleaning device in hot water of 40 DEG C to fill the bathtub, 2 grams per liter dose detergent, start the hydraulic massage for about 5 minutes, stop the pump drainage, and then fill the cold water, start the hydraulic massage for about 3 minutes, stop the pump drainage and clean the bathtub.

5, the cylinder surface dirt, can be used wet towels with neutral detergent wipe, this process can be repeated three times, can be smooth as new.

6, chrome plating nursing: application of clean cloth will wipe polishing wax chromium surface wipe clean with cloth stained with a little, do not use rough surface wipe.

7, gold plated, chrome plated parts do not need regular cleaning.

8, do not use a hard object, blade struck scratching bathtub surface also should not contact surface to heat the bath cigarette butts or higher than 70 DEG C.

9, do not use rough surface and utensils, containing chemical solvents or particles clean cylinder surface.

10, after the bath is used, should drain water and disconnect the power supply.

11, return water and nozzle, such as hair and other debris blockage, can be screwed clean.

12, do not use more than 80 degrees Celsius hot water, such as repeated use of hot water will reduce the life of the cylinder, the correct method is to put cold water and then put hot water.

13, do not start the water pump in the bathtub without water.

14, hydraulic massage should avoid debris or other items will return port plug, resulting in excessive pump load, causes the pump overheating, burn pump.

15, the use of such as bath bath agent, should be in the bathtub after use, rinse with water and wipe dry. After each use, should promptly rinse with water bath, emptying the water, and dry with a soft cloth, to prevent the generation of water within the ventilation pipe and metal rust.

Faucet, shower hardware use and maintenance method:

1, please use the water to tap and use a soft cotton cloth and wipe dry cleaners, cloth or paper towel and any acidic cleaning agent, polishing abrasive or detergent or soap and other things do not use any abrasive surface leading wipe out.

2, due to the usual use of all kinds of detergent, shower gel, such as long-term survival in the chrome surface will cause the surface of the leading surface degradation and directly affect the surface quality of hardware. Please at least a week cleaning with a soft cloth to clean a metal surface is best to use a neutral, such as bilizhu.

3, for the hard to remove stubborn dirt, surface fouling film and stains, etc.. Please use the glass cleaning liquid mild liquid detergent, colorless or without abrasion polishing liquid cleaning and washing with water to remove all the leading cleaning faucet to remove all cleaner and wipe dry with a soft cotton cloth.

Use and maintenance of PVC bathroom cabinet:

1, PVC cabinet should be away from 70 degrees above the heat source, to prevent softening deformation.

2, the operation should try to avoid using sharp objects to mesa, door, in order to avoid scratches.

3, the general material of the table, there are bubbles and gaps, if the color of the liquid penetration which will cause stains or discoloration, it should be avoided dye or hair dye directly on the table.

4, should avoid stagnant water on the table for a long time, otherwise long regret deformation.

5, should avoid the erosion of chemical substances, all kinds of benzene solvent and resin solvent should not be used to clean the surface.

6, door hinge and handle loosening and influence, should be timely adjustment.